1) these are stress ratngs. exposure of devices to any of these conditons may adversely afect long-term reliability. 2) (1.5mm from case 10sec max.) 3) all specifcatons typical at ta= 25c, nominal input voltage and full load unless otherwise specifed. 4) the informaton and specifcaton contained in this data sheet are believed to be correct at tme of publicaton. however rsg accepts no responsibility for consequences arising from printng errors or inaccuracies. specifcatons are subject to change without notce. dc/dc-converter rs7-s20/d20 2.0w unregulated single & dual output ? 7 pin sil package ? 5200vdc high isolaton ? low coupling capacity ? long term short circuit protecton ? low ripple and noise ? efciency up to 85% ? operatng temperature range -40 ~ +95c ? non conductve black plastc case output specification voltage accuracy: 5% line regulaton: 1.2%/ per 1% vin change max. load regulation: from 20% to 100% load: 10-12% cross regulaton (dual output): 5% short circuit protecton : indefnite (automatc recovery) ripple noise (20mhz bandwidth): 150mv pk-pk temperature coefcient: 0.03%/c capacitor load: see table input specifications voltage range: 10% max. start up time: 20ms,typ. max. input current: see table no-load/full-load input current: see table input filter: capacitors input refected ripple current : 20-40ma pk-pk typ. general specifications efciency: see table i/o isolaton voltage (60sec): 5200vdc i/o isolaton capacitance: 7pf typ. i/o isolaton resistance: 1000m ohm, min switching frequency: 50khz - 100khz humidity: 95% rel h reliability calculated mtbf : >3.3mhrs (mil-hdbk-217 f) safety standard: (designed to meet): iec 60950-1 environmental specification operatng temperature range: -40c ~+95c (see deratng curve) maximum case temperature: 100c storage temperature : -55c ~+125c cooling : nature convecton physical specifications: case material: non-conductve black plastc (ul94v-0 rated), pin material sip case: c519r-h solder -coated weight case- sip: 2.7g, typ. potng material: epoxy (ul94v-0 rated) dimmension sip: 0.76 x 0.28 x 0.39 absolute maximum ratings (1) 5v models: 9vdc max 12v models: 18vdc max 15v models: 20vdc max 24v models: 30vdc max soldering temperature: 260c max. emc specifications (2) radiated-/conducted emissions: en55022 class b see emi filter esd: iec 61000-4-2 perf.criteria a rs: iec 61000-4-3 perf.criteria a eft: iec 61000-4-4 perf.criteria a surge: iec 61000-4-5 perf.criteria a cs: iec 61000-4-6 perf.criteria a pfmf iec 61000-4-8 perf.criteria a dc/dc-converter 2.0w unregulated single & dual output we energize electronics! an acal group company we energize electronics! rsg electronic components gmbh ? sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ? rsg-electronic.de page 1 (4 ) stand juni 2016 rev 01
dc/dc-converter rs7-s20/d20 6.0w regulated single & dual output dc/dc-converter 2.0w unregulated single & dual output we energize electronics! an acal group company we energize electronics! rsg electronic components gmbh ? sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ? rsg-electronic.de page 2 (4) stand juni 2016 rev 01 vl2 2w unregulated single & dual output 2 model selection guide m ode l nu mb er in p ut vo lt age r ange (v dc) in p ut cu rren t o utpu t v oltage ( vd c) ou tpu t c urre nt full loa d (m a) e ffi ci en cy @ fl (% , t yp.) ca pac it or lo ad @ fl ( f, m ax.) n o - lo ad (m a, m ax ) full lo ad (m a , typ .) rs7 -0503s20a5 5 ( 4. 5 ~ 5 .5 ) 40 435 3 .3 5 00 76 10 00 rs7-05 0 5s20a5 5 ( 4. 5 ~ 5 .5 ) 40 507 5 4 00 79 47 0 rs7-05 0 9s20a5 5 ( 4. 5 ~ 5 .5 ) 40 482 9 2 22 83 47 0 rs7-05 1 2s20a5 5 ( 4. 5 ~ 5 .5 ) 40 477 1 2 1 67 84 22 0 rs7-05 1 5s20a5 5 ( 4. 5 ~ 5 .5 ) 40 471 1 5 1 33 85 22 0 rs7-1203s20a5 12 ( 10. 8 ~ 1 3.2 ) 30 186 3 .3 5 00 74 10 00 rs7-12 0 5s20a5 12 ( 10. 8 ~ 1 3.2 ) 30 211 5 4 00 79 47 0 rs7-12 0 9s20a5 12 ( 10. 8 ~ 1 3.2 ) 30 204 9 2 22 82 47 0 rs7-12 1 2s20a5 12 ( 10. 8 ~ 1 3.2 ) 30 204 1 2 1 67 82 22 0 rs7-12 1 5s20a5 12 ( 10. 8 ~ 1 3.2 ) 30 201 1 5 1 33 83 22 0 rs7 -1503s20a5 15 ( 13. 5 ~ 1 6.5 ) 25 149 3 .3 5 00 74 10 00 rs7-15 0 5s20a5 15 ( 13. 5 ~ 1 6.5 ) 25 171 5 4 00 78 47 0 rs7-15 0 9s20a5 15 ( 13. 5 ~ 1 6.5 ) 25 165 9 2 22 81 47 0 rs7-15 1 2s20a5 15 ( 13. 5 ~ 1 6.5 ) 25 163 1 2 1 67 82 22 0 rs7-15 1 5s20a5 15 ( 13. 5 ~ 1 6.5 ) 25 161 1 5 1 33 83 22 0 rs7 -2403s20a5 24 ( 21. 6 ~ 2 6.4 ) 20 95 3 .3 5 00 73 10 00 rs7-24 0 5s20a5 24 ( 21. 6 ~ 2 6.4 ) 20 107 5 4 00 78 47 0 rs7-24 0 9s20a5 24 ( 21. 6 ~ 2 6.4 ) 20 103 9 2 22 81 47 0 rs7-24 1 2s20a5 24 ( 21. 6 ~ 2 6.4 ) 20 103 1 2 1 67 81 22 0 rs7-24 1 5s20a5 24 ( 21. 6 ~ 2 6.4 ) 20 103 1 5 1 33 81 22 0 rs7 -0505d20a5 5 ( 4. 5 ~ 5 .5 ) 40 507 5 2 00 79 2 20 rs7 -0509d20a5 5 ( 4. 5 ~ 5 .5 ) 40 488 9 1 11 82 2 20 rs7 -0512d20a5 5 ( 4. 5 ~ 5 .5 ) 40 482 12 8 3.3 83 1 00 rs7 -0515d20a5 5 ( 4. 5 ~ 5 .5 ) 40 477 15 6 6.7 84 1 00 rs7-05 1509d20a5 5 ( 4. 5 ~ 5 .5 ) 40 482 +1 5/ - 9 +6 6. 7/ - 11 1 83 +1 00 / - 2 20 rs7 -1205d20a5 12 ( 10. 8 ~ 1 3.2 ) 30 211 5 2 00 79 2 20 rs7 -1209d20a5 12 ( 10. 8 ~ 1 3.2 ) 30 206 9 1 11 81 2 20 rs7 -1212d20a5 12 ( 10. 8 ~ 1 3.2 ) 30 201 12 8 3.3 83 1 00 rs7 -1215d20a5 12 ( 10. 8 ~ 1 3.2 ) 30 201 15 6 6.7 83 1 00 rs7-12 1509d20a5 12 ( 10. 8 ~ 1 3.2 ) 30 209 +1 5/ - 9 +6 6. 7/ - 11 1 80 +1 00 / - 2 20 rs7 -1505d20a5 15 ( 13. 5 ~ 1 6.5 ) 25 169 5 2 00 79 2 20 rs7 -1509d20a5 15 ( 13. 5 ~ 1 6.5 ) 25 165 9 1 11 81 2 20 rs7 -1512d20a5 15 ( 13. 5 ~ 1 6.5 ) 25 161 12 8 3.3 83 1 00 rs7 -1515d20a5 15 ( 13. 5 ~ 1 6.5 ) 25 163 15 6 6.7 82 1 00 rs7-15 1509d20a5 15 ( 13. 5 ~ 1 6.5 ) 25 165 +1 5/ - 9 +6 6. 7/ - 11 1 81 +1 00 / - 2 20 rs7-2405d 20a5 24 ( 21. 6 ~ 2 6.4 ) 20 106 5 2 00 79 2 20 rs7 -2409d20a5 24 ( 21. 6 ~ 2 6.4 ) 20 105 9 1 11 80 2 20 rs7 -2412d20a5 24 ( 21. 6 ~ 2 6.4 ) 20 103 12 8 3.3 81 1 00 rs -24 15d20a5 24 ( 21. 6 ~ 2 6.4 ) 20 102 15 6 6.7 82 1 00 rs7-24 1509d20a5 24 ( 21. 6 ~ 2 6.4 ) 20 105 +1 5/ - 9 +6 6. 7/ - 11 1 80 +1 00 / - 2 20 the information and specifications contained in this data sheet are believed to be correct at time of publication. however, motien technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. specifications are subject to change without notice. no rights under any patent accompany the sale of any such product(s) or information contained h erein. part number structure vl2 - 12 15 ss series name vl2 - 12 15 09 s series name output type s - dual output input voltage 05 - 5v 12 - 12v 15 - 15v output type ss - single output s - dual output input voltage 05 - 5v 12 - 12v - output voltage 15 - 15v 09 - - 9v 24 - 24v output voltage 3r3 - 3.3v 05 - 5v 09 - 9v 12 - 12v 15 - 15v 24 - 24v + output voltage 15 - 15v r s 7 - xx xx x xx power (w) input t ype a x code inter nal isolation (kvdc)
dc/dc-converter rs7-s20/d20 6.0w regulated single & dual output dc/dc-converter 2.0w unregulated single & dual output we energize electronics! an acal group company we energize electronics! rsg electronic components gmbh ? sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ? rsg-electronic.de page 3 (4) stand juni 2016 rev 01 vl2 2w unregulated single & dual output 3 derating curve 100% 75% 50% 25% - 40 - 20 0 20 40 60 65 80 95 100 120 ambient temperature( c +vout +vin dc/dc converter - vin - vout note 1. one load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within 5%. 2. ripple/noise measured with a 10f electrolytic capacitor and 0.1f ceramic capacitor. 3. tested by minimal vin and constant resistive load. 4. measured input reflected ripple current with a simulated so urce inductance of 12h and a source capacitor cin(47f, esr<1.0? at 100khz). 5. "nature convection" is usually about 30 - 65 lfm but is not equal t o s till air (0 lfm). 6. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 7. the vl2 series standard module meets emi classb with external components. for more detail information, please contact with motien. 8. input components (c1,d1) are used to help meet surge test requirement fo r t he module. c1 and d1 recommended nichicon uhe series and littelfuse smdj series. 9. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. s. o. a. test configurations input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12 h) and a source capacitor cin(47 f, esr<1.0? at 100khz) at nominal input and full load. o utput ripple & noise measurement test use a 10f electrolytic capacitor and 0.1f ceramic capacitor. the scope measurement bandwidth is 0 - 20mhz. li n current probe cin load resistive load eft & surge filter input components (c1,d1) are used to help meet surge test requirement for the module. +vout +vin emi filter input filter components (c1,c2,c3,l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. +vout +vin l + c1 d1 dc/dc converter load c1 c2 c3 dc/dc converter load - vin - vout - vin - vout d1:transient voltage suppression diodes the information and specifications contained in this data sheet are believed to be correct at time of publication. however, motien technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. specifications are subject to change without notice. no rights under any patent accompany the sale of any such product(s) or information contained herein. c1 c2 c3 l r s7 - 05xxxx 1206,4.7 f /16v x x 6.8 h r s7 - 12xxxx 1206,22 f /25v x x 6.8 h r s7 - 15xxxx 1206,22 f /25v x x 6.8 h r s7 - 24xxxx 1210,10 f /35v 1210,10 f /35v 1210,10 f /35v 10 h c1 d1 r s7 - 05xxxx 330 f /50v smdj9.0a r s7 - 12xxxx 330 f /50v smdj13a r s7 - 15xxxx 330 f /50v smdj18a r s7 - 24xxxx 1000 f /35v smdj24a 10 f copper strip +vout single dc/dc converter + scope 0.1 f - vout outpu t powe r vl2 2w unregulated single & dual output derating ure 2 2 2 2 u c cc c note 1. one load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within 5%. 2. ripple/noise measured with a 10f electrolytic capacitor and 0.1f ceramic capacitor. 3. tested by minimal vin and constant resistive load. 4. measured input reflected ripple current with a simulated so urce inductance of 12h and a source capacitor cin(47f, esr<1.0? at 100khz). 5. "nature convection" is usually about 30 - 65 lfm but is not equal t o s till air (0 lfm). 6. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 7. the vl2 series standard module meets emi classb with external components. for more detail information, please contact with motien. 8. input components (c1,d1) are used to help meet surge test requirement fo r t he module. c1 and d1 recommended nichicon uhe series and littelfuse smdj series. 9. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. s. o. a. test configurations input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12 h) and a source capacitor cin(47 f, esr<1.0? at 100khz) at nominal input and full load. o utput ripple & noise measurement test use a 10f electrolytic capacitor and 0.1f ceramic capacitor. the scope measurement bandwidth is 0 - 20mhz. li n current probe cin load resistive load eft & surge filter input components (c1,d1) are used to help meet surge test requirement for the module. +vout +vin emi filter input filter components (c1,c2,c3,l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. +vout +vin l + c1 d1 dc/dc converter load c1 c2 c3 dc/dc converter load - vin - vout - vin - vout d1:transient voltage suppression diodes the information and specifications contained in this data sheet are believed to be correct at time of publication. however, motien technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. specifications are subject to change without notice. no rights under any patent accompany the sale of any such product(s) or information contained herein. c1 c2 c3 l r s7 - 05xxxx 1206,4.7 f /16v x x 6.8 h r s7 - 12xxxx 1206,22 f /25v x x 6.8 h r s7 - 15xxxx 1206,22 f /25v x x 6.8 h r s7 - 24xxxx 1210,10 f /35v 1210,10 f /35v 1210,10 f /35v 10 h c1 d1 r s7 - 05xxxx 330 f /50v smdj9.0a r s7 - 12xxxx 330 f /50v smdj13a r s7 - 15xxxx 330 f /50v smdj18a r s7 - 24xxxx 1000 f /35v smdj24a 10 f copper strip +vout single dc/dc converter + scope 0.1 f - vout outpu t powe r test configurations
dc/dc-converter rs7-s20/d20 6.0w regulated single & dual output dc/dc-converter 2.0w unregulated single & dual output we energize electronics! an acal group company we energize electronics! rsg electronic components gmbh ? sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ? rsg-electronic.de page 4 (4) stand juni 2016 rev 01 vl2 2w unregulated single & dual output 4 xxxx 1 2 5 6 7 : m echanical specifications 0.50 (0.02) 9.50 (0.37) 2.54 19.5 (0.76) printed face dc-d c converter rs 7 -x xxxx xs20a5 r s g 3.00 (0.12) 7.20 (0.28) 10.0 (0.39) 7.20 (0.28) (0.10) 15.24 (0.60) 2.13 (0.08) 2.00 (0.08) 0.50 (0.02) 0.50 (0.02) 2.13 (0.08) 0.25 (0.01) 7 p in sil package notes : all dimensions are typical in millimeters ( inches ). 1. pin diameter: 0.50.05 ( 0.020.002 ) 2. pin pitch and length tolerance: 0.35 ( 0.014 ) 3. pin to case tolerance: 0.5 ( 0.02 ) 4. case tolerance: 0.5 ( 0.02 ) drawing approved: last update : may.13.2016 m o t i en iso iso ie n r t t i t t t r www.motien.com.tw email : sales@motien.com.tw pin connections pin number single dual 1 +v input +v input 2 - v input - v input 5 - v output - v output 6 n.p. common 7 +v output +v output mechanical specifications the models listed here are just standard type. if you need a product with special specifcaton or you have questons regarding packing standards (tube oder tape/reel) as well as applicaton support, please contact our specialists: sales @ rsg-electronic.de or +49 69-984047-41/-28
|
